作者：周迎春1, 杨学泉2
作者单位：1. 华中科技大学, 湖北武汉 430074;
2. 湖北省计量测试技术研究院, 湖北武汉 430071
关键词：定向X射线探伤仪; 辐射角; 中心偏移; 针像拍片法
摘要：
辐射角及中心偏移,是定向X射线探伤仪的重要技术指标。应用现行的X射线探伤仪计量检定规程和相关行业标准中的检测方法,检测成本高,仪器设备昂贵。为研究一种简单易行、准确可靠的检测方法,提出了针像拍片成像法,通过借助一套简单辅助器具,不但可检测辐射角及中心偏移,而且定位准确。实验结果表明,该方法简便,解决了射线窗口中心定位问题,提高了检测准确度,其准确度可与准确定位时剂量扫描法相媲美,并可解决剂量扫描法不适用的情况,完全满足实际检测要求。
Researching on radiation angle and central deviation test method for X-ray directional flaw detectors
ZHOU Ying-chun1, YANG Xue-quan2
1. Huazhong University of Science and Technology, Wuhuan 430074, China;
2. Hubei Institute of Measurement and Testing Technology, Wuhan 430071, China
Abstract: Radiation angle and central deviation is important parameters of an X-ray directional flaw detector. In the active verification regulation and industry standards of X-ray flaw detectors, the measurement methods require high testing costs and expensive apparatuses. For developing a simple, accurate and reliable method, the pinimage roentgenography is presented. By a suit of simple assistive devices, this method can not only be used for measuring radiation angle and central deviation, but also can position the geometric centre accurately. The experimental results show that this method is simple, can accurately position the geometric centre of the radiation window, enhances the measurement accuracy, and its accuracy can be comparable to the dose scanning method when geometric positioning is accurate, and can be used to test in some cases that the dose scanning method is not suitable. The method fully meets the actual requirements.
Keywords: X-ray directional flaw detector; Radiation angle; Central deviation; Pin-image roentgenography
2008, 34(5): 98-102 收稿日期: 2008-3-26;收到修改稿日期: 2008-6-11
基金项目:
作者简介: 周迎春(1969-),男,高级工程师,博士,主要从事电离辐射测量以及相关检测仪器设备的研究开发。
参考文献
[1] JB/T 9402-1999, 工业X射线, 探伤机性能测试方法[S]. 机械工业部仪器仪表综合技术经济研究所, 1999.
[2] JB/T 7413-1994, 携带式工业X射线探伤机[S].机械工业部仪器仪表综合技术经济研究所, 1994.
[3] JB/T7412-1994, 固定式(移动式)工业X射线探伤仪[S]. 北京:机械工业部仪器仪表综合技术经济研究所, 1994.
[4] JJG 40-2001, X射线探伤机检定规程[S].北京:中国计量出版社, 2002.
[5] 袁松. 工业X射线探伤机的检验[J]. 试验技术与试验机, 2002, 42(3):96-98.
[6] 梁晓镕, 陈小安, 杨刚炜, 等.X射线探伤机检定方法讨论[J].自动化与仪表, 2003, 18(4):76-77.
[7] GB/T 9582-1998, 工业射线胶片ISO感光度和平均斜率的测定(用X和γ射线曝光)[S].北京:中国标准出版社, 1998.
[8] JJF 1033-2008, 计量标准考核规范[S].北京:中国计量出版社, 2008.
