作者：崔金雷1, 侯俊亮1, 肖辉朗1, 王修益2, 曲利峰3, 何小旭1
作者单位：1. 四川航天系统工程研究所，四川 成都 610100;
2. 四川航天电子设备研究所，四川 成都 610100;
3. 陆军装备部驻成都第三军代室，四川 成都 610000
关键词：预制破片;初速;爆轰产物;能量泄漏
摘要：
为降低现有预制破片初速计算方法误差，基于战斗部作用后能量释放和预制破片驱动过程，应用量纲分析理论，分析误差产生的原因，以Gurney公式为基础，构建爆轰产物泄漏系数表征的修正模型。利用非线性分析软件AUTODYN-3D对球形和立方体两种常见的预制破片爆炸驱动的过程进行数值模拟，采用数值模拟结果对构建的模型参数进行标定，提出一种考虑爆轰产物能量泄漏的预制破片初速的修正计算模型，并设计实施相应的试验对计算模型进行验证，结果显示该修正计算模型精度相比原公式平均提高14%以上。该文结论可为破片式杀爆战斗部设计计算和毁伤效应准确评估提供参考。
An amended method of calculating initial velocity of prefabricated fragments
CUI Jinlei1, HOU Junliang1, XIAO Huilang1, WANG Xiuyi2, QU Lifeng3, HE Xiaoxu1
1. Sichuan Aerospace Institute of Systematic Engineering, Chengdu 610100, China;
2. Sichuan Institute of Aerospace Electronics, Chengdu 610100, China;
3. The Third Office of Chengdu Military Representative Bureau of Army Equipment Department, Chengdu 610000, China
Abstract: In order to reduce the error in the calculation method of the initial velocity of the existing prefabricated fragments, energy release of the explosive and fragment-driving process of fragment warhead after detonated are analyzed. An amended method of calculating initial velocity of prefabricated fragments is proposed based on Gurney formula. Coefficients are defined to denote the leakage effects of explosion gas based on dimensional analysis. Accelerating of two typical shaped fragments driven by explosion gas is simulated by AUTODYN-3D software and the relationship between leakage effects and warheads with different fragment shapes and sizes is obtained. Experiments are designed for validation and the precision is enhanced by 14% on average as a result. The method can provide a reference for design calculation and accurate evaluation of the damage effect of prefabricated fragmental warheads.
Keywords: prefabricated fragments;initial velocity;explosion gas;energy leakage
2021, 47(10):19-26 收稿日期: 2021-04-30;收到修改稿日期: 2021-05-22
基金项目:
作者简介: 崔金雷（1991-），男，河南修武县人，工程师，硕士，研究方向为安全工程、武器装备体系总体设计
参考文献
[1] 蒋浩征. 杀伤战斗部破片飞散初速v0的计算[J]. 兵工学报, 1980(1): 68-79
[2] GURNEY R. The initial velocities of fragments from bombs, shells and grenades[R]. Maryland : BRL, 1943.
[3] 牟仁德, 贺世美. 内爆炸圆管破片初速研究[J]. 航空材料学报, 2006, 26(3): 140-143
[4] 邢恩峰, 钱建平, 赵国志. 装药结构参数对轴向预制破片抛掷速度的影响[J]. 火炸药学, 2007, 30(1): 49-53
[5] 杨云川, 厉相宝, 万仁毅. 预制破片初速和飞散角的数值模拟[J]. 弹箭与制导学报, 2009, 29(4): 96-98
[6] 邓吉平, 胡毅亭, 贾宪振, 等. 爆炸驱动球形破片飞散的数值模拟[J]. 弹道学报, 2008, 20(4): 96-99
[7] 陈兴旺, 王金相, 唐奎, 等. 爆炸驱动多层球形破片初速场分析[J]. 振动与冲击, 2020, 39(16): 129-134
[8] 苗春壮, 梁增友, 邓德志, 等. 不同形状预控破片成形及毁伤效应研究[J]. 火炮发射与控制学报, 2018, 39(4): 11-15
[9] 凌琦, 何勇, 何源. 定向战斗部破片飞散的数值模拟与试验研究[J]. 振动与冲击, 2017, 36(3): 234-241
[10] 蒋建伟, 冯顺山, 何顺录. 一种用于评价和计算杀伤威力的数学模型[J]. 北京理工大学学报, 1992, 12(2): 90-96
[11] 王树山. 终点效应学[M]. 北京: 科学出版社, 2020.
